quadient DS-77iQ Manual Download Page 96 | Manualshive

Page: 96 / 156

background image

The conditions are:

• No multi-feed is used for the BREs.
• The document directly under the BRE must have a height of at least 60 mm (2.4

inch) more than the BRE.

• The height of the BRE is more than the set fold length.
• The folding mode is either V-fold or C-fold (no Z-fold).
• The BRE must be shorter than the envelope height.

The whole BRE offset is based on friction between documents within a set. Therefore it is
necessary to make use of these conditions to reduce the risk of bad transporting, folding
and inserting.

It is possible to use the BRE offset for a BRE and an enclosure
(card) in one set. The extra condition is that this enclosure is equal
to or smaller than the set address fold and should be placed direct
underneath the BRE in the set.

License information

License information shows information on the open source software that is used in the
system.

92

| Page 92 | Jul-11-2022 07:45 | Settings menu

6

English

«
...
94
95
96
97
98
...
»

Summary of Contents for DS-77iQ





























































































































































Reviews:

No comments

Related manuals for DS-77iQ

Brand: NCR Pages: 10

Brand: Raise3D Pages: 32

Brand: OKIDATA Pages: 13

Brand: Konica Minolta Pages: 40

Brand: GCC Technologies Pages: 97

ProJet x60 Series

Brand: 3D Systems Pages: 72

Imagistics 2500

Brand: Axis Pages: 16

Brand: Xiamen Hanin Electronic Technology Pages: 27

Brand: LaserLine Pages: 14

Brand: Rapid Shape Pages: 44

Brand: Linux Pages: 8

Brand: SPRT Pages: 14

IMAGE L2550DW Series

Brand: G&G Pages: 147

Brand: Konica Minolta Pages: 8

Brand: Savin Pages: 132

4400B - Phaser B/W Laser Printer

Brand: Xerox Pages: 24

Brand: Xerox Pages: 2

DocumentCentre C400 Series

Brand: Xerox Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands