quadient DS-77iQ Manual Download Page 46

Page: 46 / 156

Create a test mail set

Create a Test Mail Set

Before starting an existing job or a new, manual created job, it is possible to create a test
mail set.

This test run is intended to validate the settings of the Document System:

• Check if the address is correctly positioned behind the envelope window.

See

Adjusting the Address position

on page 46.

• Inspect and adjust the stop position of the envelope. See

Adjusting the Envelope

Insert fingers

on page 45.

• Check the fold settings for one set. See

Fold settings

on page 34.

When you tap the [1x] button, you can choose between test mail sets:

• Selected exit: creates one mail set that leaves the system at the defined exit. Use

this option to test the complete process.

• Envelope stop position: separates one envelope and transports the envelope to the

envelope stop position. Use this option to verify and adjust the envelope stop position.

After a test mail set, the system asks if the mail set is ok or not ok. When you select not
ok, you are guided through a wizard that helps you to find the cause.

| Page 42 | Jul-11-2022 07:45 | Working with Jobs

English

Summary of Contents for DS-77iQ





























































































































































Search results

Summary of Contents for DS-77iQ

Reviews:

Related manuals for DS-77iQ

Brands by name

Popular brands

quadient DS-77iQ, Manual

Search results

Summary of Contents for DS-77iQ

Reviews:

Related manuals for DS-77iQ

Brands by name

Popular brands