quadient DS-77iQ Manual Download Page 69 | Manualshive

Page: 69 / 156

background image

Document Separation

The term ‘Document separation’ refers to the adjustment required for separating the upper
document from the rest of the documents in the stack. This prevents pulling too much
documents from the stack at the same time.

The document separation for the automatic feeders is set automatically; there are no manual
adjustments needed.

Feeders 3st can be special feeders. The document separation for special feeders must be
adjusted manually. While special feeder trays fit in all positions, adjusting the separation
is only possible when they are fitted on position 1 and 2.

To adjust the separation of special feeders follow the instructions as described in

the Separation of Special Feeders

on page 48.

maxiFeeder

Adjust the maxiFeeder Side Guides

Adjust the side guides:

Take a stack of documents/BREs and place them in the feeder tray.
BREs with flap down and leading (top side pointing to system).

1.

5

English

65

| Page 65 | Jul-11-2022 07:45 | Loading the System

«
...
67
68
69
70
71
...
»

Summary of Contents for DS-77iQ





























































































































































Reviews:

No comments

Related manuals for DS-77iQ

Brand: TierTime Pages: 28

Brand: Nehoc Pages: 9

Brand: SPRT Pages: 14

Brand: Commodore Pages: 188

Brand: A&D Pages: 102

Brand: Lexmark Pages: 489

Brand: Canon Pages: 2

Brand: Canon Pages: 4

Brand: Canon Pages: 2

PIXMA MG6220 Installing

Brand: Canon Pages: 4

PIXMA MG7500 Series

Brand: Canon Pages: 4

Brand: Canon Pages: 676

Brand: Canon Pages: 2

Brand: DataCard Pages: 204

Brand: WOOSIM Pages: 20

Brand: Canon Pages: 174

Brand: Canon Pages: 168

Brand: Star Micronics Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands