quadient DS-77iQ Manual Download Page 121 | Manualshive

Page: 121 / 156

background image

OMR general remarks

General remarks:

• In case of OMR the marks must always be used in the sequence as shown in the

figure.

• If a function is suppressed the following function will move upwards one line.
• The mark definition is a service setting.

An Example of OMR Code

In the figure the legend for the following example is shown. In this example, a set of 8
sheets with one selective feed and three sequence check marks is shown.

• The first position is used for the start mark which must be printed on every sheet.
• The second mark position is used for the insert/accumulate command. A printed

mark means insert, no mark means accumulate. Therefore the mark is printed on
the last sheet of the set.

• Position 3 is reserved for selective feed from the enclosure feeder. Print a mark on

position 3 when a selective feed from the enclosure feeder is required. The marks
are printed on the last sheet of the set.

• Position 4, 5 and 6 are used for the sequence check marks. In this case a three mark

sequence check is used.

8

English

117

| Page 117 | Jul-11-2022 07:45 | Reading

«
...
119
120
121
122
123
...
»

Summary of Contents for DS-77iQ





























































































































































Reviews:

No comments

Related manuals for DS-77iQ

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: GCC Technologies Pages: 63

Brand: gCreate Pages: 9

Brand: GCC Technologies Pages: 9

Brand: GCC Technologies Pages: 12

Brand: gCreate Pages: 21

Brand: GCC Technologies Pages: 199

Brand: Xerox Pages: 4

Brand: Lexmark Pages: 455

Brand: Olympus Pages: 2

Brand: Raymarine Pages: 135

Brand: VASTEX Pages: 15

Brand: Canon Pages: 12

Brand: Xerox Pages: 14

Brand: Oki Pages: 2

Brand: SINTERIT Pages: 16

Brand: MIMAKI Pages: 30

Printpix NC-400D

Brand: FujiFilm Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands