quadient DS-77iQ Manual Download Page 136

Page: 136 / 156

Error messages

When an error occurs the touch screen shows a screen with the following information:

• An indication of the area in which the error occurred
• An error description
• A suggested solution behind the arrow
• An event message number; use this number in case that you call support

Tap (i) Details to view more information about the occurred error and about the possible
actions to avoid the error from re-occurring.

After solving the problem, tap [x] to reset the error (the error screen will disappear).

Special Errors

• Reading errors (when reading is enabled)

The document set is diverted. The operator must remove the document set and has
to complete the set manually!

• Technical errors

The display shows a message. The error cannot be solved by operating personnel
and assistance of the service support is needed.

132

| Page 132 | Jul-11-2022 07:45 | Fault Finding

English

Summary of Contents for DS-77iQ





























































































































































Search results

Summary of Contents for DS-77iQ

Reviews:

Related manuals for DS-77iQ

Brands by name

Popular brands

quadient DS-77iQ, Manual

Search results

Summary of Contents for DS-77iQ

Reviews:

Related manuals for DS-77iQ

Brands by name

Popular brands