background image

Lighting switch

When the lighting switch is 
on"

"position,all the illu-

-minating lamps will be off. 
Shift the lighting switch to"    "
position,you can light up the
headlamp, taillight, position 
lamp, and instrument light.

Front brake lever

The front brake lever is located 

at the right grip and when grasping 

the lever toward the grip, the 

braking is applied.

Turn signal lamp switch

To send out right turn signal, push the switch to "     ".
To send out left turn signal,push the switch to "      ".
The button will automatically return to the central 
position when it is released. To turn off the turn signal 
light, push down the reset button in the middle after 
the switch returns to the central position, .

Horn switch:

 

Press this button and the horn will promptly send out 
sounds.

Electric starting switch

 

While switching on the main lock and holding the 
front brake or rear brake lever (the side stand is in 
back state), push the starting button and you can 

Before starting the engine, please read the relevant 
instructions on start-up.

Rear brake lever

The rear brake lever is located 

at the left grip and when grasping 
the lever toward the grip, the 
braking is applied.

Try to lift up the end of the seat to confirm whether it is 

locked in. Before locking, confirm the seat key is not 

inside the trunk.

Notice 

Note

start the engine only when the main switch is on"    " 
position. 

USER'S MANUAL

5

Summary of Contents for Achille 150






































Reviews: