background image

Starting lever

Screw out the starting lever 
towards the outer side of the 
engine. Tread the starting lever 

slightly with foot till the gear 

gets engaged and then start the 
engine by fast and forceful 
treading of the starting lever.

When using starting lever, use throttle grip to refuel slightly 
and this will help motorcycle starting.

Trunk

The trunk is located under the seat 

When loading, never exceed the 

max.Load of 10.0 kg(22lbs).

Steering lock 

To lock the steering handle, 

make left rotation of motorcycle 
steering handle through to the 

end, and when the key is in 
"      " position,press the main 

switch and then turn counter
c1ockwise directly to "     " 

Fuel tank cap

Open: Open the fuel tank 
protection cover and just turn the 

fuel tank cap counter clockwise. 

Close: Join the bulge on the fuel 
tank cap with the groove on the 
fuel tank and just turn the cap 
clockwise.

Before riding motorcycle, make sure the fuel tank cap has 

When riding the motorcycle, never turn the key to"     "
position.

position to lock the steering handle, and pull out the 
key. Turn the counter clockwise to "     " position and 

you can unlock the steering lock. 

Warning

Warning

been properly installed and locked to its original place.

Notice 

USER'S MANUAL

6

Summary of Contents for Achille 150






































Reviews: