Printronix L1024 Maintenance Manual Download Page 40

Page: 40 / 372

2–22

Chapter 2 – Clamshell

Remove 1 Screw and the Tension Spring, then remove the Pivot Shaft from the Assembly to
free the Hinge Frame from the Clamshell Frame.

NOTE:

The steps above can be performed for either Hinge Assembly.

2.7.2 Reassembly and Replacement

Reverse Steps 1 through 6 above.

2.7.3 Adjustment

Adjust the spring tension (on the side of the hinge) so that when the Clamshell is opened fully and
released, the Clamshell falls to a 30

angle and then stops. This adjustment prevents the Clamshell from

injuring the fingers of operators or service personnel.

ÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÏÏ

ÌÌÌ

ÎÎ

Spring
Retention
Plate

Spring Tension
Adjustment Screw

Figure 2–5. Clamshell Hinge Adjustment

2.7.4 Troubleshooting

See Chapter 13 for troubleshooting information.

Summary of Contents for L1024





















































































































































































































































































































































































Search results

Summary of Contents for L1024

Reviews:

Related manuals for L1024

Brands by name

Popular brands

Printronix L1024, Maintenance Manual

Search results

Summary of Contents for L1024

Reviews:

Related manuals for L1024

Brands by name

Popular brands