Printronix L1024 Maintenance Manual Download Page 192 | Manualshive

Page: 192 / 372

background image

9–26

Chapter 9 – Controllers and Floppy Disk Drives

9.9.1 Removal and Disassembly

NOTE:

Some printers will have only one Floppy Disk Drive installed. The second,
or Drive B, Floppy Disk Drive is an option. This procedure is written
assuming that the printer being serviced has both Floppy Disk Drives
installed.

1.

Open the Clamshell. Remove any paper present in the printer. Remove the OPC Drum Unit,
the Developer Unit, and the Waste Toner Container.

2.

Remove the Front and Rear Paper Guides from the printer.

3.

Remove the Floppy Disks from the Floppy Disk Drives.

4.

Disconnect the Power Cord and Data Cable from the rear of the printer.

5.

Remove the plastic Floppy Disk Drive Guide (Bezel) from the front of the printer by pressing
in on the Locking Tabs.

See Figure 9–10.

6.

Remove the 4 Screws from the printer Back Panel that secure the Data Controller Board.

See

Figure 9–1 on page 9–10.

CAUTION:

The Floppy Disk Drive Data and Power Cables must be disconnected
from the Data Controller Board before the board can be removed from
the printer.

7.

Slide the Data Controller Board out of the printer part of the way, until you can gain access to
the Floppy Disk Drive Power Cable Connector (J5) and Data Cable Connector (J10) on the
board.

See Figure 9–1 on page 9–10.

8.

Disconnect the Floppy Disk Drive Power Cable from Connector J5 on the Data Controller
Board.

9.

Disconnect the Floppy Disk Drive Data Cable from Connector J10 on the Data Controller
Board.

10. Slide the Data Controller Board out the rest of the way, and remove it from the printer.

11. With paper and all Consumables removed, especially the Waste Toner Container, turn the

printer upside down. Carefully press on the 4 corners of the Bottom Cover to release the
Locking Tabs from the Base Plate and remove the Bottom Cover. Turn the printer rightside
up.

See Figure 9–4 on page 9–16.

12. Remove 2 Screws from the front and 1 Screw from the left side of the Floppy Disk Drive

Frame.

See Figure 9–10.

13. Remove the Floppy Disk Drive Frame (with Drives and Drive Cables attached) from the

printer Base Frame, through the front opening of the printer.

«
...
190
191
192
193
194
...
»

Summary of Contents for L1024





















































































































































































































































































































































































Reviews:

No comments

Related manuals for L1024

Brand: Datecs Pages: 29

Brand: Xerox Pages: 89

Brand: TallyGenicom Pages: 310

Brand: TallyGenicom Pages: 330

Brand: Canon Pages: 4

7400DT - Phaser Color LED Printer

Brand: Xerox Pages: 20

Brand: A&D Pages: 16

mC-Print3 MCP31LB

Brand: Star Pages: 12

Brand: Oki Pages: 2

Tally Colour Laser T8006e

Brand: Tally Pages: 200

Brand: Felix Storch Pages: 46

Brand: Oki Pages: 109

Brand: BIG TREE TECH Pages: 11

Brand: imagistics Pages: 2

Brand: Oki Pages: 64

Brand: Xerox Pages: 4

Brand: Xiamen Sojet Electronics Pages: 37

Brand: Canon Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands