Printronix L1024 Maintenance Manual Download Page 118 | Manualshive

Page: 118 / 372

background image

7–22

Chapter 7 – Fuser Subsystem

7.4.1 Removal and Disassembly

1.

Open the Clamshell and remove the OPC and Developer Units, as well as any paper present
in the Printer.

See Figure 7–1.

2.

Remove the Fuser Heat Shield, then remove the Lamp Connector Cover by removing 1
Screw. Disconnect the Fuser Lamp and Thermistor Connectors from the Stepper Motor Board
Frame.

See Figure 7–1.

3.

Remove the Right Inside Cover by removing 1 Screw, then pressing down on the Warning
Label at the front of the Cover. This releases the Locking Tab from the Right Side Cover.

See

Figure 7–1

.

NOTE:

Upon installation, the groove on the bottom of the Right Inside Cover
should straddle the top edge of the right side of the Tractor Frame.

See

Detail 7–3 in Figure 7–1.

4.

Remove the Tractor Paper Guide by removing 1 Screw from the center rear of the Tractor
Frame.

5.

Open the Paper Exit Guide of the Fuser Base so that it is not in contact with the Fuser Roller
Assembly.

6.

Depress the Fuser Assembly Retaining Lever on each side of the Printer so that the Fuser
Assembly is free to move.

7.

Lift the Fuser Assembly free of the Fuser Base, then remove it from the Printer.

8.

Disconnect the Fuser Sensor Board by removing the Cable at Connector J1.

9.

Open the Printer Front Cover, then remove the LCD Control Panel by removing 2 Screws.

10. Remove the Right Side Cover by removing 3 Screws.

11. Loosen, but do not remove, 2 Screws on the top of the Stepper Motor Board Frame. Remove

the Frame Cover, and disconnect 2 Cables from Connectors CN5 and CN6 on the Stepper
Motor Board.

12. Remove 2 Screws from the rear of the Fuser Base and remove it from the printer.

DISASSEMBLY

13. Remove the Paper Exit Guide by removing 2 Springs, then lifting the Guide off of the Shaft on

the Fuser Base Frame.

See Figures 7–3 and 7–4.

«
...
116
117
118
119
120
...
»

Summary of Contents for L1024





















































































































































































































































































































































































Reviews:

No comments

Related manuals for L1024

Brand: m3d Pages: 23

Brand: m3d Pages: 26

Brand: 3D Systems Pages: 16

Brand: 3D Systems Pages: 28

Brand: 3D Systems Pages: 21

Brand: 3D Systems Pages: 25

Brand: 3D Systems Pages: 23

Brand: 3D Systems Pages: 35

Brand: 3D Systems Pages: 7

Brand: 3D Systems Pages: 13

Brand: 3D Systems Pages: 19

Brand: 3D Systems Pages: 13

Brand: 3D Systems Pages: 2

Brand: 3D Systems Pages: 2

Cubify CUBEX Duo

Brand: 3D Systems Pages: 10

Brand: 3D Systems Pages: 7

Brand: 3DGence Pages: 24

Brand: 3DGence Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands