Contents Explanation of LCD Indicator
ⴘ
Battery Voltage / CV
Regeneration Mode
/
Charge Mode
/
Power Supply Mode
/
Condition Test
:
Choose the working standard(official) battery voltage by using
ⵒ
UP button or
ⵓ
DOWN button under the SET located the arrow (
ⶺ
).
You can choose 6V, 8V and 12V and go on to the next work by pushing
ⵑ
ENTER button.
Condition Test
is 12V Only.
Discharge Mode
: Input final discharge voltage (CV; Cut off Voltage) by using
ⵒ
UP button or
ⵓ
DOWN button under the SET located
the arrow (
ⶺ
). After set-up CV, go on to the next work by using
ⵑ
ENTER button.
Function selection
You can select any work you want by pushing
ⵐ
SELECT button, that function is
displayed in
ⴜ
of the above screen. You can choose 5 functions : REGENERATION, CHARGE, POWER SUPPLY, DISCHARGE, CONDITION TEST.
ⴙ
Capacity (Ah) / Current (A)
Regeneration Mode
/
Charge Mode
/
Condition Test
:
Set-up the Battery Capacity(Ah) by using
ⵒ
UP button or
ⵓ
DOWN button
under the SET located the arrow (
ⶺ
).
After set-up the Capacity, go on to the next work by using
ⵑ
ENTER button.
Power Supply Mode
:
Designate working battery hourly supply current(A) by using
ⵒ
UP button or
ⵓ
DOWN button under the SET located
the arrow (
ⶺ
). Normally set-up 1/10 (10% of Capacity) carrying Current(A) of Battery Capacity(Ah).
Discharge Mode
: Designate working battery discharge current(A) by using
ⵒ
UP button or
ⵓ
DOWN button under the SET located
the arrow (
ⶺ
). (The international standard discharge current of Car battery is 25A.) After set-up CV, go on to the
next work by using
ⵑ
ENTER button.
ⴛ
I R
/ CCA
Regardless of function selection connect the machine and the battery, after pushing
ⵑ
ENTER button about 2 seconds, you can
check the connected battery’s IR(Internal Resistance) value and CCA (Cold Cranking Ampere). These are current battery
conditions(Before). After finishing the work, IR value and CCA value are displayed automatically in After part.
These are regenerated (or charged) battery conditions(After).
ⴜ
Message
Work progress indication and warning message are displayed. Refer to the below items.
ⴚ
Run Time (H:M)
Regeneration Mode
/
Charge Mode
:
In regeneration mode working time is displayed in SET part automatically, the elapsed time is
displayed in WORK part.
Power Supply Mode
:
You can set up working battery progress time by using
ⵒ
UP button or
ⵓ
DOWN button. You have to set up
working time according to the condition of the battery to be regenerated or charged.
Discharge Mode
: You can set-up discharge time by using
ⵒ
UP button or
ⵓ
DOWN button under the SET located the arrow.
(Car battery doesn’t need to designate discharge time). After designation go on to the next work by using
ⵑ
ENTER button.
6
Displayed contents explanation of LCD information representation indicator
(Bad Judgement)
That is a message displayed stopping the work when the battery voltage does not rise after a while
from regeneration or charge started. This is a damaged battery to be a disposal.
These messages are appeared finishing the work completely.
This message is appeared when the regeneration/charge time is passed because the supplying current is less than
set-up battery capacity or the battery cannot accept current due to the bad condition. If the battery doesn’t make the
heat (lower than 45
Ⳅ
), the battery specification can be enhanced if you regeneration/charge again.
That is a message when the supplied current is 130% over than the total capacity of the battery with over supplying.
That is a message when the displayed battery voltage is 30% less than the set-up standard(official) voltage.
That is a message when there is no voltage, the wrong connection of +, - to the battery or one or both terminals
are disconnected due to external shock in machine working.
(Machine Problem)
That is a message when the heat protection cannot be made because of the heat sink’s
temperature is risen during regeneration/charge/discharge work.
