Polaris 2009 Outlaw 450 MXR Owner'S Manual Download | Manualshive

Page: 78 / 205

background image

75

Operation

Turning Around on a Hill

If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn

around:
1. Keep your body weight uphill.
2. Pull in the clutch lever and apply the front and rear brakes.
3. When completely stopped, shut off the engine. Leaving the transmission in gear, release

the clutch lever and lock the parking brake.

4. Dismount on the uphill side of the vehicle, or on the left side if the vehicle is pointing

straight uphill.

5. Staying uphill of the ATV, turn the handlebars full left.
6. Reach across the handlebar and apply the front brakes to unlock the parking brake.

«
...
76
77
78
79
80
...
»

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Reviews:

No comments

Related manuals for 2009 Outlaw 450 MXR

Brand: KAYO MOTOR Pages: 90

Pioneer SXS500M 2018

Brand: Honda Pages: 268

LYNX RADIEN UTILITY ACE 2022 Series

Brand: BRP Pages: 252

Brand: Ardisam Pages: 8

Brand: Dinli Pages: 99

ErgoSteer SP001V9810010

Brand: FENDT Pages: 40

Brand: Yamaha Pages: 222

YXZ 1000 R SS 2023

Brand: Yamaha Pages: 216

Brand: ABI Attachments Pages: 28

Brand: Axis Pages: 63

Brand: Axis Pages: 74

Brand: Canyon Pages: 83

Brand: Can-Am Pages: 140

Brand: Ivarssons i Mestjö Pages: 32

Brand: PRONAR Pages: 25

Brand: PRONAR Pages: 150

Brand: Daimler Pages: 90

Brand: KAYO MOTOR Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands