Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 36 / 205

Safety

Safety Warnings

Hot Exhaust Systems

Exhaust system components are very hot during

and after use of the vehicle. Hot components can

cause burns and fire. Do not touch hot exhaust

system components. Always keep combustible

materials away from the exhaust system. Use

caution when traveling through tall grass,

especially dry grass.

Unauthorized Use of the ATV

Leaving the keys in the ignition can lead to

unauthorized use of the vehicle, which could

result in an accident or overturn. Always remove

the ignition key when the vehicle is not in use.

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands