Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 23 / 205

Safety

Safety Warnings

Operating on Pavement

Operating an ATV on paved surfaces (including

sidewalks, paths, parking lots and driveways)

may adversely affect the handling of the ATV and

could result in loss of control and accident or

overturn. Avoid operating the ATV on pavement.

ATV tires are designed for off-road use. If it's

unavoidable, travel slowly and avoid sudden

turns or stops.

Operating on Public Roads

Operating this ATV on public streets, roads or

highways could result in a collision with another

vehicle. Never operate the ATV on any public

street, road or highway, including dirt and gravel

roads. In many states it's unlawful to operate

ATVs on public streets, roads and highways.

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands