Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 155 / 205

152

Maintenance

Suspension Settings

Use a flat-blade screwdriver to make damping adjustments. When the adjuster screw is

turned clockwise until it stops, the damping is in the fully closed position.

Rear Shock (Standard and Limited Edition)

Front Shock (Limited Edition)

Setting

Compression Damping

Rebound Damping

Softest

20 clicks from closed

24 clicks from closed

Factory

10 clicks from closed

16 clicks from closed

Firmest

2 clicks from closed

Setting

Compression

Softest

20 clicks from closed

Factory

10 clicks from closed

Firmest

2 clicks from closed

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands