Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 77 / 205

Operation

Driving on a Sidehill (Sidehilling)

Driving on a sidehill is not recommended. Improper procedure could cause loss of control or

overturn. Avoid crossing the side of any hill unless absolutely necessary.
If crossing a sidehill is

unavoidable

, follow these precautions:

1. Slow down.
2. Lean into the hill, transferring your

upper body weight uphill while keep-

ing your feet on the footpegs.

3. If the vehicle begins to slide or tip,

quickly turn the front wheel down-

hill, if possible, or dismount on the

uphill side

immediately

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands