Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 163 / 205

160

Maintenance

Cleaning

Washing the Vehicle

If a high pressure water system is used for cleaning (not recommended), exercise extreme

caution. The water may damage components and could remove paint and decals. If warning

and safety labels are damaged, contact your Polaris dealer for free replacement. Avoid direct-

ing the water stream at the following items:
• Wheel bearings
• Electrical components and wiring
• Transmission seals

• Brakes
• Cab and body panels
• Labels and decals

Grease all zerk fittings immediately after washing. Allow the engine to run for a while to

evaporate any water that may have entered the engine or exhaust system.

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands