Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 27 / 205

Safety

Safety Warnings

Descending Hills Improperly

Improperly descending a hill could cause loss of control or

overturn.
• Always follow proper procedures for traveling down hills as

described in the owner's manual.

NOTE:

A special tech-

nique is required when braking while traveling downhill. See

page 78.

• Always descend a hill with the transmission in forward gear.

Do not descend a hill with the transmission in neutral.

• Always check the terrain carefully before descending a hill.
• Shift your weight rearward.
• Never travel down a hill at high speed.
• Avoid traveling down a hill at an angle, which would cause

the vehicle to lean sharply to one side. Travel straight down

the hill when possible.

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands