Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 29 / 205

Safety

Safety Warnings

Stalling While Climbing a Hill

Stalling, rolling backwards or improperly dismounting while climbing a

hill could cause an overturn.
Always maintain a steady speed when climbing a hill.

If all forward speed is lost

Keep body weight uphill. Apply the front brakes gradually (right

lever). When fully stopped, apply the foot brake as well, and then lock

the parking brake.

If the ATV begins rolling downhill:

Keep weight uphill. Never apply engine power. Never apply the rear

brake while rolling backwards. Apply the front brake slowly. When

fully stopped, apply the rear brake as well, and then lock the parking

brake. Dismount on uphill side, or to either side if ATV is pointed

straight uphill. Turn the ATV around and remount, following the

procedure described in the owner's manual. See page 75.

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands