Polaris 2009 Outlaw 450 MXR Owner'S Manual Download

Page: 116 / 205

113

Maintenance

Carburetor

Normal wear from engine vibrations may cause the carburetor to supply an overly rich fuel

mixture. Replace the jet needle and the needle jet after every 180 hours of operation.

Idle Speed

Carburetor idle adjustments affect engine starting behavior. A proper idle speed of 1700-

1800 RPM will result in easier starting. If idle speed is unsatisfactory, make adjustments as

outlined on page 113.

Idle Speed

1. Position the vehicle on a level surface. Lock the parking

brake. Place the transmission in neutral.

2. Start the engine and allow it to idle for five minutes, or until

operating temperature is reached.

3. Turn the idle adjusting wheel (1) until idle speed reaches

1700-1800 RPM. If idle speed is unsatisfactory after per-

forming this procedure, see your Polaris dealer for informa-

tion about jetting changes.

Summary of Contents for 2009 Outlaw 450 MXR














































































































































































































Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands

Polaris 2009 Outlaw 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2009 Outlaw 450 MXR

Reviews:

Related manuals for 2009 Outlaw 450 MXR

Brands by name

Popular brands