PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 43

Page: 43 / 72

Cut the template along the lines using scissors and punch out all four holes.

Locate the top of the template at the dimensions shown. Make sure the
short edge of the template is flush with the front side of the 2" x 4" x 46

³⁄₄

board as shown. Mark the top edge and the Right-Side top holes of the
template as shown. Repeat for all three dimensions.

Then repeat markings on the inside of the left 2" x 4" x 46

³⁄₄

board rotating

the template so the markings are a mirror image of each other. Drill using a

¹⁄₈

" drill bit at the marked locations.

Items for STEP 39:

(1) Printed Template

12"

24"

36"

Flush with
this edge

Mark the top
edge & the
two top holes

r L

CUT OUT THIS TEMPLATE

Mark
these two
boards

" x

³⁄₄

Ground

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands