PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 57

Page: 57 / 72

Items for step 40:

(1) 2" x 4" x 75

³⁄₄

" board

(1) triangle bracket
(2) #8 x 1

¹⁄₄

" deck screws

Attach triangle bracket onto 2" x 4" x 75

³⁄₄

" board.

Lay bracket flat on the board. Slide bracket until the stops
on the underside are tight against the board and the edge
of the bracket is flush with the corner of the board as shown.

Use the bracket as a drill guide and drill two

¹₈

" holes 1" deep into the board. Attach with

#8 x 1

¹⁄₄

" deck screws.

Again use the bracket as a drill guide and
drill three

³₈

" holes completely through the

board in the locations shown.

2" x

4" x

³⁄₄

Note: When correctly positioned,

this edge of bracket will

be parallel with this

edge of the

board.

flush at corner only

stops

drill

2" x

4" x

³⁄₄

2" x

4" x

³⁄₄

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands