PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 22

Page: 22 / 72

¹|₂

90º

" x

⁷|₈

" x

Items for STEP 17:

(1) 2" x 6" x 88" board
(1) 2" x 6" x 35

⁷₈

" board

(4) #8 x 1

¹₄

" deck screws

drill

Helpful Hint:

If you are standing here looking at the
assembly, the A-Frame will be on your
right side, the single post will be on your
left side and the brackets will be pointing
at each other.

Lay out the single post assembly and the A-Frame
assembly approximately 92

¹₂

" apart. Use remaining

unused boards to elevate approximately 3".

Place 2" x 6" x 88" and 2" x 6" x 35

⁷₈

" beam boards

under brackets as shown.

Hold beam tight against bracket. Beam

should rest on

³₈

" x

³₄

" hex bolts and

top of post when in proper position.
Be sure A-Frame is square (90˚)
with beam.

Use brackets as a drill guide and drill

¹₈

" holes

1" deep into the beam and attach with #8 x 1

¹₄

deck screws as shown.

Again, use brackets as a drill guide and drill

³₈

" holes completely through the beam as shown.

drill

¹⁄₈

”

Swing Station Assembly

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands