PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 55

Page: 55 / 72

Items for step 38:

(1) 2" x 4" x 46

³⁄₄

" board

(2) #8 x 1

¹⁄₄

" deck screws

Use the bracket as a drill guide and drill two

¹₈

" holes 1"

deep into the boards. Attach with #8 x 1

¹₄

" deck screws.

Again use the bracket as a drill guide and drill two

³₈

" holes

completely through the board.

Use the hole in the 2" x 4" x 75

³⁄₄

" board as a drill guide

and drill a

³₈

" hole completely through both boards.

drill

flush at corner only

Attach 2" x 4" x 46

³⁄₄

" board.

Lay the assembly from the previous step on the board. Slide
assembly until the stops on the underside of bracket are tight
against the board and the corner of the 2" x 4" x 75

³⁄₄

" board is

flush with the end of the 2" x 4" x 46

³⁄₄

" board as shown.

x 4

" x

³⁄₄

2" x 4

" x 46

³⁄₄

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands