PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 71

Page: 71 / 72

Fig. 2

back view

COMPONENTS - Mounting Instructions

USE THE INSTALLATION INSTRUCTIONS AND MOUNTING HARDWARE

WHICH ARE SUPPLIED WITH THE FOLLOWING COMPONENTS

AIR RIDER (PS 7958)

CLIMBING ROPE

1. Tie five knots, equally spaced, for climbing grips.

(Fig. 1)

2. Insert rope through top hole and tie a knot with 4"

remaining.

3. Insert opposite end through bottom hole, pull tight and

tie a knot while keeping rope snug.

4. Secure both ends with staples

provided (2 each end).

(Fig. 2)

Fig. 1

front view

CLIMBING ROCKS

1. Position rocks at desired

location.

2. Mark pilot holes.

3. Drill

³₈

" holes completely

through boards.

4. Hammer in T-nuts from back side.

5. Secure with two

¹⁄₄

" x 1" machine

screws and

¹⁄₄

" split lock washers provided.

SWING SEAT • GYM RINGS

1. Attach coated ends of chains onto play component using
Quick-Link Connectors provided. Tighten securely with an
adjustable wrench.

2. Hook uncoated ends of chain onto Swing Hangers provided.

3. Customize the height of your

swing

gym rings

anywhere

in the

Adjustment Zone

, to fit your child.

Warning: Failure to tighten Quick Links

securely could result in injury.

Adjustment

Zone

Swing Chain Spacing:

10" minimum spacing is required from the closest point of all
other rides or stationary objects

Gym Ring Chain Spacing:

¹₂

" minimum spacing is required from the closest point of all

other rides or stationary objects.

WATER SLIDE KIT
(PS 8840)

PLAY HANDLES

1. Position Play Handle at desired

location.

2. Mark pilot holes.

3. Drill

¹₈

" holes 1" deep.

4. Secure with

14 x 1

¹₄

" pan head

screws provided.

DECORATIVE KIT (PS 7980)

DISCOVERY TELESCOPE

1. Determine desired location for pivot.

2. Drill a

¹⁄₈

" diameter hole 1" deep.

3. Fasten pivot with #8 x 2

¹⁄₂

" deck

screw provided.

4. Snap Discovery Telescope onto pivot.

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands