PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 54

Page: 54 / 72

CLIMBING BAR ASSEMBLY

Items for step 37:

(1) 2" x 4" x 75

³⁄₄

" board (cut previously)

(1) triangle bracket
(2) #8 x 1

¹⁄₄

" deck screws

Attach triangle bracket onto 2" x 4" x 75

³⁄₄

" board.

Lay bracket flat on the board. Slide bracket until
the stops on the underside are tight against the
board and the edge of the bracket is flush with
the corner of the board as shown.

Use the bracket as a drill guide and drill two

¹₈

" holes 1" deep into the board. Attach with

#8 x 1

¹⁄₄

" deck screws.

Again use the bracket as a drill guide and
drill three

³₈

" holes completely through the

board in the locations shown.

Note: When correctly positioned,

this edge of bracket will
be parallel with this
edge of the
board.

flush at corner only

stops

drill

Underside of bracket showing correct positioning

x 4

" x

³⁄₄

x 4

" x

³⁄₄

x 4

" x

³⁄₄

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands