PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 38

Page: 38 / 72

STURDY-FRAME BRACE INSTALLATION

Step 33:

Remove the top

³⁄₈

" x 3

¹⁄₂

" hex bolt, washers

and lock nut from the post support as shown.
(Save these parts because they will be used
in the next step.)

Items for Step 34:

(1) Sturdy-Frame Brace
(1) 3

¹⁄₂

" hex bolt

(2)

³⁄₈

" washers

(1)

³⁄₈

" lock nut

Install the Sturdy-Frame Brace as shown and
secure with

³⁄₈

" x 3

¹⁄₂

" hex bolt, washers and

lock nut removed in previous step.

Make sure brace is square to beam. Using
the brace as a template, drill a

³⁄₈

" hole com-

pletely through the beam.

Items for Step 35:

(1) 3

¹⁄₂

" hex bolt

(2)

³⁄₈

" washers

(1)

³⁄₈

" lock nut

Secure the Sturdy-Frame Brace to the beam
with

³⁄₈

" x 3

¹⁄₂

" hex bolt, washers and lock nut.

NOTE: It is easiest to remove this

bolt by continuing to rotate in
a counterclockwise direction.

Removed on
previous step

}

³⁄₈

" x 3

¹⁄₂

hex bolt

³⁄₈

" x 3

¹⁄₂

hex bolt

³⁄₈

" x

¹⁄₂

hex

Drill

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands