PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 26

Page: 26 / 72

Items for STEP 21:

(1)

³₈

" x 4

¹₂

" bolt

(2)

³₈

" washers

(1)

³₈

" lock nut

CONNECT TOWER AND SWING BEAM

On the post of tower assembly where the beam will be attached, measure and
mark hole location (7" down and 1

⁵₈

" from edge) as shown.

(Fig. 1)

Drill a

³₈

" hole completely through the board.

On the open hole of the beam assembly use a 1

¹₈

" spade bit and counterbore

approximately

¹₄

" deep to ensure that the threads of the bolt are at least flush to

the end of the nut when installed.

(Fig. 2)

Lift beam to an upright position and attach to tower using one

³₈

" x 4

¹₂

" hex bolt,

³₈

" washers and

³₈

" lock nut as shown.

(Fig. 2)

⁵₈

Fig. 1

Counterbore

Fig. 2

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands