PLAYSTAR VARSITY BRONZE Safety Manual & Assembly Instructions Download Page 66

Page: 66 / 72

Items for STEP 37:

(1) 1" x 4" x 29

¹₂

" board

(4) #8 x 1

¹₂

" deck screws

Caution: Failure to pre-drill and
counter-sink the boards may result in
split lumber.

AGES

7 & 8

OLE

ATTERNS

STOP

The Adventure Tunnel Kit (PS 8876) must be installed now.

Follow the building instructions included with the Adventure Tunnel Kit

skipping Step 2 ONLY. Then continue with these instructions.

Attach one pre-drilled and counter-sank 1" x 4" x 29

¹₂

board on the

outside

of tower at the approximate

dimension shown.

Center board on gap and secure with #8 x 1

¹⁄₂

" deck

screws. Do not over tighten the screws.

Note: Gap between boards must not exceed
3

¹₂

" or a head entrapment could exist.

¹⁄

₂

Summary of Contents for VARSITY BRONZE









































































Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands

PLAYSTAR VARSITY BRONZE, Safety Manual & Assembly Instructions

Search results

Summary of Contents for VARSITY BRONZE

Reviews:

Related manuals for VARSITY BRONZE

Brands by name

Popular brands