Pitney Bowes Relay 2500 User Manual Download Page 97

Page: 97 / 182

Adding Sealer Solution

1. When the Add sealing solution icon flashes, add E-Z Seal® Solution.

Icon Description

Add sealing solution

2. Open the sealer bottle cover hinge located at the rear, right side of the inserter and remove the

bottle.

3. Fill the bottle with the solution to the level indicated.

4. Place the sealer bottle in position in the inserter and close the cover.

NOTE

: If the sealer unit was completely empty, allow time for the fresh solution to soak through the

sealer before resuming operation. This helps ensure a good seal.

NOTE

: We recommend Pitney Bowes E-Z Seal to minimize algae growth and scale build-up.

Running a Job

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 90 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Related manuals for Relay 2500

Brands by name

Popular brands

Pitney Bowes Relay 2500, User Manual

Search results

Summary of Contents for Relay 2500

Reviews:

Related manuals for Relay 2500

Brands by name

Popular brands