Pitney Bowes Relay 2500 User Manual Download Page 168

Page: 168 / 182

Error Messages

This

BAD OMR MARK

THICKNESS

Review the specifications for OMR & Make necessary adjustments to printed markings as

appropriate

CALL SERVICE

Power the inserter off and on. If the message is still displayed, call Service.

CHECK /CLEAR FEEDER

Feeder indicated has failed to feed material. Remove material from the feed tray, reload

and restart the inserter.

ENVELOPE FEEDER

Verify envelopes are loaded correctly

Verify there aren't any envelopes jammed under the envelope feed rollers

CHECK FOLD PLATE

Fold plate indicated is not located correctly. Remove fold plate and relocate.

CHECK INVERTER

Envelope inverter unit has not set to its correct position.

Open the inverter cover and check for material

Close the cover and restart

CHECK LAST MAILPIECE

Envelope has failed to open.

Check the envelopes are loaded correctly

Reload the envelopes and restart machine

CLEAR FOLD PLATE

Material was detected inside the fold plate indicated on the display.

Remove the fold plate and check for any material

Install fold plate

Troubleshooting

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 161 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Pitney Bowes Relay 2500, User Manual, Page: 168 / 182

Search results

Summary of Contents for Relay 2500

Reviews: