Pitney Bowes Relay 2500 User Manual Download Page 143

Page: 143 / 182

Clearing Material Jams in the Envelope Feeder Area

1. Pull the release lever in the direction of the arrow.

2. Lift the envelope area feed rollers for access to the jam.

3. Remove the jammed material. If necessary,

use the manual advance knob

to move the material

backwards.

NOTE

: Envelope jams in the Envelope Feeder area may be hard to see. After lifting the envelope

feed rollers, carefully reach under the rollers to feel for jammed material.

4. Relatch the feed rollers after you remove the jam.

5. Release the envelope area feed rollers and let them rest in position.

6. Push the rollers firmly down until they latch into position.

Error Recovery and Clearing Material Jams

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 136 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Brands by name

Popular brands

Pitney Bowes Relay 2500, User Manual

Search results

Summary of Contents for Relay 2500

Reviews:

Brands by name

Popular brands