Pitney Bowes Relay 2500 User Manual Download Page 125

Page: 125 / 182

Barcode Scanning Error Messages

Message

Issue

Solution

No OMR marks

- Barcode was not seen by scanner

- Paper not loaded correctly

- Reposition the barcode scanner

- Check paper orientation

- Confirm barcode sheet is in the right feeder

Expected first sheet

of set

Expected first sheet of set was not detected

by barcode scanner

- Add missing page(s)

- Correct sheet sequence

Not a new envelope

First sheet of set was detected; rest of sheets

were expected

Add missing sheets and/or correct your sheet

sequence

OMR: Sequence

error

Sequence number in barcode is not

sequential with the previous page fed

Add missing sheets and/or correct the sheet

sequence

OMR: SF Marks

Inconsistent

n/a

Not used for barcode jobs

OMR: Set to Large

Sheet set contains too many sheets

Refer to fold types and thickness limits in this

guide

OMR: End of Batch –

Ready to Run

Indicates machine has stopped for “End of

Batch.”

Operator can manually sort envelopes in stacker

Mode change re-

check feeders

Check the sheet and insert feeder settings for

the job before exiting setup mode

Barcode Scanning

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 118 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Pitney Bowes Relay 2500, User Manual, Page: 125 / 182

Search results

Summary of Contents for Relay 2500

Reviews: