Pitney Bowes Relay 2500 User Manual Download Page 170

Page: 170 / 182

This

FOLD PLATES NOT SET

The fold plates has not set to the correct position.

Remove fold plates and check for any material

Install the fold plates and restart the inserter

MANUAL FEED TIMEOUT

Material feed has not been detected within a predetermined time.

In manual feed mode, material must be fed within a set time

Restart the machine by pressing

Start

PAPER SHORT

The inserter detected that the material used is too short in length.

Check the actual material length matches the length displayed

If correct, request another trial piece

PAPER SHORT CHECK

STACKER

The inserter detected that the material used is too short in length.

Check the actual material length matches the length displayed

If correct, request another trial piece

SET LEVER

The manual feed lever is in the incorrect position for the mode of running.

Move the manual feed lever to the correct position (left position: manual; right:

automatic).

STREAM FEED

The inserter detected two sheets fed together from the feed tray indicated.

Remove the material from the inserter. Reload and restart the inserter

STREAM FEED CHECK

STACKER

The inserter detected two sheets fed together from the feed tray indicated.

Remove the stream feed from the stacker. Reload and restart the inserter

SYSTEM ERROR POWER

DOWN

A fault has been detected in the main software.

Switch the inserter off and on and retry. If the problem persists, call for Service.

TRAY EMPTY

The tray indicated has no material. Reload the tray and press

Start

Troubleshooting

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 163 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Brands by name

Popular brands

Pitney Bowes Relay 2500, User Manual

Search results

Summary of Contents for Relay 2500

Reviews:

Brands by name

Popular brands