Pitney Bowes Relay 2500 User Manual Download Page 174

Page: 174 / 182

Fold Configurations (material length limits before folding)

Fold Type

Measurement

Single-fold

6 inches (150 mm) - 12 inches (314 mm)

C-fold

8 inches (200 mm) - 14 inches (356 mm)

Z-fold

8.5 inches (215 mm) - 14 inches (356 mm)

Double-fold

10.5 inches (270 mm) - 16 inches (406 mm)

Double Document Detector Material Range

Minimum

Maximum

18 lb (70 gsm)

32 lb (120 gsm)

Feed Tray Capacity

Maximum of 325 sheets of 20 lb (80 gsm) paper

Manual Feed Mode

For manual feed applications sheet feeder 1 is used, plus the insert feeder if required.

Inserter processes stapled sets of up to five sheets of 20 lb. bond (80 gsm) up to a maximum total
weight of 100 lbs. (400 gsm) per set.

Maximum compressed thickness after folding must not exceed 0.078 inch (2 mm).

Using glossy or coated sheets is

not

recommended

Specifications

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 167 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Pitney Bowes Relay 2500, User Manual, Page: 174 / 182

Search results

Summary of Contents for Relay 2500

Reviews: