Pioneer Elite SC-35, Operating Instructions Manual

Page: 42 / 148

Connecting your equipment 03
42
En
Switching components on and off using
the 12 volt trigger
You can connect com p onents in you r system (such as a
sc r een o r pr ojecto r ) to this r eceive r so that they switch on
o r off using 12 volt t r igge r s when you select an in p ut
function. Howeve r , you must s p ecify which in p ut
functions switch on the t r igge r using the
The Input Setup
menu
on p age 45. Note that this will only wo r k with
com p onents that have a standby mode.
• Connect the 12 V TRIGGER jack of this receiver to
the 12 V trigger of another component.
Use a cable with a mono mini- p lug on each end fo r the
connection.
Afte r you’ve s p ecified the in p ut functions that will switch
on the t r igge r , you’ll be able to switch the com p onent on
o r off just by pr essing the in p ut function(s) you’ve set on
p age 45.
It is also p ossible to have the com p onent switch not when
the in p ut function is switched, but when
HDMI OUT
is
switched. Fo r details, see
HDMI Setup
on p age 73.
Plugging in the receiver
Only p lug in afte r you have connected all you r
com p onents to this r eceive r , including the s p eake r s.
1 Plug the supplied power cord into the AC IN socket
on the back of the receiver.
2 Plug the other end into a power outlet.
1
CAUTION
• Handle the p owe r co r d by the p lug p a r t. Do not p ull
out the p lug by tugging the co r d, and neve r touch the
p owe r co r d when you r hands a r e wet, as this could
cause a sho r t ci r cuit o r elect r ic shock. Do not p lace
the unit, a p iece of fu r nitu r e, o r othe r object on the
p owe r co r d o r p inch the co r d in any othe r way. Neve r
make a knot in the co r d o r tie it with othe r cables. The
p owe r co r ds should be r outed so that they a r e not
likely to be ste pp ed on. A damaged p owe r co r d can
cause a fi r e o r give you an elect r ic shock. Check the
p owe r co r d once in a while. If you find it damaged,
ask you r nea r est Pionee r autho r ized inde p endent
se r vice com p any fo r a r e p lacement.
• Do not use any p owe r co r d othe r than the one
su pp lied with this unit.
• Do not use the su pp lied p owe r co r d fo r any p u rp ose
othe r than that desc r ibed below.
• The r eceive r should be disconnected by r emoving the
mains p lug f r om the wall socket when not in r egula r
use, e.g., when on vacation.
• Make su r e the blue  STANDBY/ON light has gone
out befo r e un p lugging.
• If you have connected s p eake r s with a 6
Ω
im p edance, change the im p edance setting befo r e
tu r ning on the p owe r .
12 V
TRIGGER
1
2
(OUTPUT
12 V
TOTAL
150 mA MAX)
RS-232C
HDMI
ASSIGNABLE
COMPONENT VIDEO
ASSIGNABLE
MONITOR OUT
ZONE 2 OUT
IN
Y
ANTENNA
FM UNBAL 75 AM LOOP
CD
IN
VIDE
MONITOR
OUT
ZONE2
OUT
ZONE3
OUT
DVD
IN
TV/SAT
IN
VIDEO
IN
DVR/BDR PHONO
IN OUT IN
P
R
P
B
1
IN BD
IN 1
IN
2
IN
3
OUT 1
(CONTROL)
OUT
1 4
(DVD)
IN 2 (DVR/BDR)
IN 3
(VIDEO)
CONTROL
CU-RF100
IR
IN
IN
IN
OUT
OUT
1
2
IN
4
(OUTPUT 5 V
150 mA MAX)
SPEAKERS
Class 2 Wiring
SIGNAL
GND
R
FRONT HEIGHT/W
SEE INSTRUCTION
MANUAL
SELECTABLE
VOIR LE MODE
D'EMPLOI
SELECTABLE
12 V TRIGGER
INPUT
Note
1 Afte r this r eceive r is connected to an AC outlet, a 2 second to 10 second HDMI initialization pr ocess begins. You cannot ca rr y out any
o p e r ations du r ing this pr ocess. The
HDMI
indicato r in the f r ont p anel dis p lay blinks du r ing this pr ocess, and you can tu r n on this r eceive r
once it has sto pp ed blinking. When you set the Control with HDMI to OFF , you can ski p this pr ocess. Fo r details about the Control with HDMI
featu r e, see
Control with HDMI function
on p age 72.
SC-37_35_UXJCB.book 42 ページ ２０１０年３月９日 火曜日 午前９時３２分