Pioneer Elite SC-35, Operating Instructions Manual

Page: 98 / 148

Controlling the rest of your system (In case of SC-35) 10
98
En
3 Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver’s remote control.
The LED blinks once and flashes continuously.
• The r emote cont r ols should be 3 cm (1 inch) a p a r t.
4 Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver’s remote control.
If the LED lights fo r one second, the setting has been
successfully com p leted.
1
5 To program additional signals for the current
component repeat steps 3 and 4.
To pr og r am signals fo r anothe r com p onent, exit and
r e p eat ste p s 2 th r ough 4.
6 Press R.SETUP to exit the programming mode.
Erasing one of the remote control
button settings
This e r ases one of the buttons you have pr og r ammed and
r esto r es the button to the facto r y default.
1 Press and hold R.SETUP, then press “7” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess R.SETUP .
2 Press the input function button corresponding to
the command to be erased, then press ENTER.
The LED flashes once.
3 Press and hold the button to be erased for three
seconds.
If the LED lights fo r one second, the e r asing has been
successfully com p leted.
4 Repeat step 3 to erase other buttons.
5 Press R.SETUP to exit the erasing mode.
Erasing all learnt settings that are in
one input function
This o p e r ation e r ases all the o p e r ational settings of othe r
devices that have been pr og r ammed in one in p ut
function, and r esto r es the facto r y default.
This function is handy fo r e r asing all data pr og r ammed
fo r devices no longe r being used.
1 Press and hold R.SETUP, then press “9” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess
R.SETUP
.
2 Press and hold the input function button
corresponding to the command to be erased for three
seconds.
If the LED lights fo r one second, the e r asing has been
successfully com p leted.
Direct function
• Default setting: On
You can use the di r ect function featu r e to cont r ol one
com p onent using the r emote cont r ol while at the same
time using you r r eceive r to p lay a diffe r ent com p onent.
This could let you, fo r exam p le, use the r emote cont r ol to
set u p and listen to a CD on the r eceive r , and then use the
r emote cont r ol to r ewind a ta p e in you r VCR while you
continue to listen to you r CD p laye r .
When di r ect function is on, any com p onent you select
(using the in p ut function buttons) will be selected by both
the r eceive r and the r emote cont r ol. When you tu r n di r ect
function off, you can o p e r ate the r emote cont r ol without
affecting the r eceive r .
1 Press and hold R.SETUP, then press “5” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess
R.SETUP
.
2 Press the input function button for the component
you want to control.
3 Press “1” (On) or “0” (Off) to switch the direct
function mode.
If the LED lights fo r one second, the setting has been
successfully com p leted.
If the LED flashes th r ee times, the setting has failed.
4 Press R.SETUP to exit the setup.
Note
1 • Note that inte r fe r ence f r om TVs o r othe r devices will sometimes r esult in the r emote cont r ol lea r ning the w r ong signal.
• Some commands f r om othe r r emote cont r ols cannot be lea r ned, but in most cases the r emotes just need to be moved close r togethe r o r
fa r the r a p a r t.
• If the LED flashes fo r five seconds, it means the memo r y is full. See
Erasing all learnt settings that are in one input function
on p age 98 to
e r ase a pr og r ammed button you’ r e not using to f r ee u p mo r e memo r y (note that some signals may take mo r e memo r y than othe r s).
3 cm
(1 inch)
This r eceive r ’s
r emote cont r ol
Othe r r emote
cont r ol
SC-37_35_UXJCB.book 98 ページ ２０１０年３月９日 火曜日 午前９時３２分