Additional information
13
126
En
Settings
Can’t record video.
• Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video
cable is used for connecting both the recorder and the video source (the one you want to record) to
this receiver.
Noisy, intermittent, or distorted
picture.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the
video quality may just be poor (with some video game units, for example). The picture quality may
also depend on the settings, etc. of your display device. Switch off the video converter and reconnect
the source and display device using the same type of connection (component or composite), then
start playback again.
Video signals are not output
from the component terminal.
• When a monitor only compatible with resolutions of 480i is connected to the component terminal
and another monitor is connected to the HDMI terminal, the video signals may not be output to the
monitor connected to the component terminal. If this happens, do the following:
– Turn off the power of the monitor connected to the HDMI terminal.
– Change the
VIDEO PARAMETER
menu
RES
setting.
– Video signals from the HDMI terminal cannot be output to the component terminals. Input the
video signals from the player or other source to the composite or component terminals. When using
the component terminal, assign it at
Input Setup
.
The picture’s movement is
unnatural.
• When Resolution under
VIDEO PARAMETER
is set to 1080/24p, the picture may not be displayed
properly for some source materials. In this case, set the resolution to something other than 1080/24p
(page 78).
Symptom
Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see
also
Problems when using the Auto MCACC Setup
on page 45). If the noise level cannot be kept low
enough, you will have to set up the surround sound manually (page 114).
• When using only one surround back speaker, connect it to the
SURROUND BACK L
(Single)
terminals.
• To use a 5.1-channel speaker set, use the surround speakers for the surround channel, not the
surround back channel.
• Make sure there are no obstacles between the speakers and the microphone.
• If
Reverse Phase
is displayed, try the following:
– The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.
– Depending on the type of speakers and their installation conditions,
Reverse Phase
may be
displayed even if the speakers are properly connected. If this happens, select
GO NEXT
and continue.
– If the speaker is not pointed to the microphone (listening position) or when using speakers that
affect the phase (dipole speakers, reflective speakers, etc.), it may not be possible to properly identify
the polarity.
After using the Auto MCACC
Setup, the speaker size setting
is incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.
Switch off all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (bass reproduction capabilities of the speakers, room size,
speaker placement, etc.) this may occur in some cases. Change the speaker setting manually in
Speaker Setting
on page 115, and use the
ALL (Keep SP System)
option for the
Auto MCACC
menu
in
Automatic MCACC (Expert)
on page 104 if this is a recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 107)
properly.
• Check that the speakers are all in phase (make sure the positive (
+
) and negative (
–
) terminals are
matched up properly).
The display shows
KEY LOCK
ON
when you try to make
settings.
• With the receiver in standby, press
STANDBY/ON
for about 10 seconds while holding down
SPEAKERS
to disable the key lock.
Most recent settings have been
erased.
• The power cord was disconnected from the wall while adjusting this setting.
• Settings are only stored if all the zones are turned off. Turn off all the zones before unplugging the
power cord.
Symptom
Remedy
12he_Additional_info.fm 126 ページ ２０１０年４月２０日 火曜日 午前１１時１４分
Summary of Contents for Elite SC-35
Page 145: ...Additional information 13 145 En 12he_Additional_info fm 145 ページ ２０１０年４月２０日 火曜日 午前１１時１５分 ...
Page 146: ...Additional information 13 146 En SC 37_35_UXJCB book 146 ページ ２０１０年３月９日 火曜日 午前９時３２分 ...
Page 147: ...Additional information 13 147 En SC 37_35_UXJCB book 147 ページ ２０１０年３月９日 火曜日 午前９時３２分 ...
