Additional information
13
128
En
Remote control
Web Control
The power turns off
automatically and some
indicator flashes, or some
indicator flashes and the power
does not turn on.
• See the
Power
section (page 122).
Symptom
Remedy
Cannot be remote controlled.
• Set the remote control unit’s remote control mode so that it matches the setting on the main unit
(see
Operating multiple receivers
on page 84 (SC-37)/page 96 (SC-35)).
• Check whether the receiver’s remote control mode is properly set (see
Remote Control Mode Setup
on page 119).
• Try replacing the batteries in the remote control (see
Loading the batteries
on page 10).
• Be sure to operate within 7 m (23 feet) and a 30º angle of the remote sensor on the front panel (see
Operating range of remote control unit
on page 11).
• Check that there are no obstacles between the receiver and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the
CONTROL IN
jacks (see
Operating other Pioneer components with
this unit’s sensor
on page 41).
SC-37 only:
Input does not
switch to Sirius or XM when
OPTION 1
or
OPTION 2
button
is pressed.
• Sirius and XM operations can no longer be performed if other preset codes are assigned to the
OPTION 1
(Sirius) or
OPTION 2
(XM) button. In this case, reset the
OPTION 1
or
OPTION 2
button
(see
Resetting the input assignment of one of the input function buttons
on page 86).
SC-37 only:
Receiver or other
components cannot be
operated by RF two-way
communications.
• There may be radio interference with other devices. Try increasing the distance from microwave
ovens, devices on a wireless LAN, other wireless devices, etc. (see
Precautions when using the Omni-
Directional RF Remote Control
on page 94).
• Try replacing the batteries in the remote control (see
Loading the batteries
on page 10).
• If the RF adapter’s LED is off, the RF adapter may not be properly connected to the receiver. Check
whether the RF adapter is properly connected to the receiver (see
Connecting the RF adapter (SC-37
only)
on page 21).
• The devices may no longer be properly paired. Pair them again (see
Pairing the RF adapter and
remote control
on page 92).
• When the remote control or main unit are reset, the RF communications function is also reset.
Make the settings again (see
Using the RF communications function
on page 91).
SC-37 only:
The remote control
display flickers.
• Flickering may occur when the remaining battery power is low. Replace the batteries with new
ones (see
Loading the batteries
on page 10).
Other components can’t be
operated with the system
remote.
• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
• When commands from the remote control units of other devices are registered using the learning
function, in some cases they may not be learned properly. In this case, register the commands again
using the learning function (see
Programming signals from other remote controls
on page 85 (SC-37)
/ page 97 (SC-35)). If they still do not work, they may be in a special format that cannot be registered
on this receiver’s remote control. Operate the device using another remote control.
Symptoms
Causes
Remedies
Top Menu screen is not
displayed on browser.
This receiver’s IP address has not been entered
into the browser correctly.
Check the receiver’s IP address and enter it
correctly in the browser (page 117).
Receiver cannot be operated
from browser.
JavaScript is disabled on the internet browser.
Enable JavaScript.
The browser is not compatible with JavaScript.
Use an internet browser that is compatible with
JavaScript.
Receiver’s power does not
turn on when the power is
turned on using the
Web
Control
function.
Network Standby
at
Network Setup
is set to
OFF
.
Set
Network Standby
at
Network Setup
to
ON
(page 118).
Symptom
Remedy
12he_Additional_info.fm 128 ページ ２０１０年４月２０日 火曜日 午前１１時１４分
Summary of Contents for Elite SC-35
Page 145: ...Additional information 13 145 En 12he_Additional_info fm 145 ページ ２０１０年４月２０日 火曜日 午前１１時１５分 ...
Page 146: ...Additional information 13 146 En SC 37_35_UXJCB book 146 ページ ２０１０年３月９日 火曜日 午前９時３２分 ...
Page 147: ...Additional information 13 147 En SC 37_35_UXJCB book 147 ページ ２０１０年３月９日 火曜日 午前９時３２分 ...
