background image

English

22

USE

To load the pellets into the hopper it is advisable to tear off the edge of

the sack and empty the sack directly into the hopper. This makes filling

easier and avoids pouring pellets on top of the stove.

Do  not  allow  sawdust  to  accumulate  on  the  bottom  of  the

hopper.

Do  leave  leftover  pellets  on  top  of  the  stove  –  they  could

catch fire!

Under  no  circumstances  remove  the  protective  grid  inside

the hopper.

When refilling with pellets while the appliance is lit, do not

let the pellet sack come into contact with hot surfaces.

• The pellet stove comes equipped with an LCD-display remote control

and radio transmitter which allow you to operate its various functions.

The remote’s range can be affected by other devices which

operate on a continuous radio frequency of 433.92 MHz , for

example radio headphones, toys, wireless mouses etc.

The remote has a range of around seven metres in conditions

where there is no interference from other sources.

• When  pressing  the  keys  to  select  the  various  functions  wait  for  a

signal  from  the  stove  that  the  selection  has  registered  before

selecting further functions. Or if you are in an adjoining room wait for

confirmation  on  the  remote’s  display.  If  the  stove  is  not  receiving

signals from the remote try bringing the remote closer to the stove.

Below are listed the various functions of the remote control’s keys.

17

13

1

7

11

12

6

14

5

8

9

10

16

2

3

4

15

1  2  3  4  5  6  

7

!

19

18

20

SET

OPT

ESC

MENU

DT2030325-00

Fig. 58

DT2030459-00

Fig. 56

DT2030460-00

Fig. 57

DT2010992-00

6.0 USE

• Do not use the stove as a cooking appliance.

• Ensure that the room in which the stove is installed is sufficiently well ventilated (fresh air intake).

• Ensure that all joints in the flue are hermetically sealed using a silicone- (not cement-) based sealant which is resistant to temperatures of up

to 250ºC and which shows no sign of deterioration.

• Check (or have checked) regularly that the flue is clean.

• Under no circumstances use fuels other than pellets.

• Remove any deposits of unused pellets left by failed ignition before restarting the stove.

Keep any inflammable object well away from the stove while it is in use (MINIMUM 80 cm from the front panel).

While in use the door must remain closed and the glass must be present and intact.

The removal of the protective grille inside the pellet hopper is strictly prohibited.

If replenishing with pellets while the stove is lit, ensure that the bag does not come into contact with any hot surfaces.

DT2010035-01

6.1 LOADING THE PELLETS - Fig. 56 - 57

DT2010730-00

6.2 REMOTE CONTROL - Fig. 58

DT2010220-05

Summary of Contents for P962

























































Reviews: