background image

English

21

INSTALLATION

• The  redirection  of  heat  to  adjoining  rooms  is  at  the  user’s

discretion.

• The Y-connector can be attached to either fan. 

• You  can  choose  to  use  only  one  of  the  fans’  outlets  to  heat

adjoing  rooms,  in  which  case  it  is  more  convenient  to  use  the

right fan. Proceed as follows:

For  convenience,  the  following  assembly  operations  should

be carried out during the installation phase first on the left fan

(as viewed from the rear) and then on the right fan (fig 47). 

1. Take off the stove’s back panel

2. Uncoil the flexible pipe from the fan’s outlet by unscrewing the

clip which holds it in place.

3. Cut around 5cm of flexible pipe (fig 48).

4. Fix the flexible pipe to the Y-connector using the clip provided

(fig 49).

5. Fix  the  Y-connector  to  the  fan’s  outlet  using  the  screws

provided (fig 50). (for the left fan see fig 52)

6. Attach the second flexible pipe to the Y connector using the clip

provided (fig 51).

7. Repeat stages 2 - 6 for the right fan.

8. Take off the sub-section of the back panel (fig 54).

9. Replace the back panel.

10. Move the stove closer to the wall (fig 53) and, using the clips

provided, fix the two flexible pipes to the pipes in the wall (fig

55).

11. Place the stove in the desired location, respecting the minimum

safety distances (see section 1.8).

DT2030230-00

DT2030229-00

DT2030178-00

DT2030175-00

Fig. 47

Fig. 48

Fig. 49

Fig. 51

DT2030232-00

Fig. 50

DT2030181-00

DT2030233-00

Fig. 54

Fig. 55

DT2030180-00

DT2030231-00

Fig.  52

Fig.  52

Fig. 53

left fan

right fan    

tightening screws

5.4 INSTALLING THE Y CONNECTOR (OPTIONAL) - Fig. 47 / 55

DT2010148-03

Summary of Contents for P962

























































Reviews: