Philips VARILITE VL1100 LED Luminaire User Manual Download Page 59

Page: 59 / 87

PERATION

: U

PDATING

OFTWARE

02.1602.0002

13 June 2017

Troubleshooting

Upload Cable LED Status Messages

Figure 3-2: USB Upload Cable

Upload Cable Warning (Error) Message

If you see a warning message (as shown in

Figure 3-3

) on your

computer screen and the USB Upload Cable is properly connected to
USB 2.0 compatible port on your computer, it may not be detected by
your computer.
•

Disconnect USB Upload Cable from computer and reconnect.

•

Reinstall USB Upload Cable Driver as described in,

Installing

PEGASUS Software

If either of the these do not resolve the error message, you may have a
defective Upload Cable. Contact customer service at 1.214.647.7880
or

[email protected]

for assistance.

Table 4: USB Upload Connector LED Colors

XLR LED Status

Meaning

Continuous

Red

Do not use the cable to download software; contact

customer service for assistance.

Continuous

Purple

Driver software is not installed.

Continuous

Blue

with

Purple

pulse every five seconds.

Cable is ready, but data is not being transmitted.

Flashing

Blue

(twice per

second)

Data is being transmitted.

LED

USB Upload

Cable

Figure 3-3: Upload Cable

Error Message

Summary of Contents for VARILITE VL1100 LED Luminaire
























































































Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands

Philips VARILITE VL1100 LED Luminaire, User Manual

Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands