Philips VARILITE VL1100 LED Luminaire User Manual Download Page 79

Page: 79 / 87

ROUBLESHOOTING

AND

AINTENANCE

02.1602.0002

13 June 2017

Troubleshooting Guide

If a problem is suspected, first try recalibrating the luminaire to prompt an error message. The chart
below provides possible causes and remedies for various error messages and/or symptoms.

CAUTION:

Some troubleshooting is included for reference only. Performing remedies marked by

gray areas will void product warranty. Refer to the Philips Entertainment Lighting Limited Warranty
card included with the product.

Table A-2: Troubleshooting Guide

Error Display

Description

Possible Cause and Remedy

Pan/No Sens

Pan Sensor Not Found

EOT flag attached to large pulley is not engaging the
EOT sensor

- Ensure flag is attached to the large pulley
- Ensure that flag passes through the sensor at a

depth sufficient to engage the sensor beam

Pan belt disconnected, extremely loose or not installed
properly

- Properly install belt between pan motor and large

pulley

Pan/Encoder/Fail

Pan Encoder Failure

Main board pan/tilt connector (J9) disconnected

- Connect main board pan/tilt connector (J9)

Pan motor disconnected

- Connect pan motor power

Encoder faulty

- Replace pan end-of-travel/encoder sensor assembly

TILT

SENS

Tilt Sensor Not Found

EOT flag attached to large pulley is not engaging the
EOT sensor

- Ensure flag is attached to the large pulley
- Ensure that flag passes through the sensor at a

depth sufficient to engage the sensor beam

Tilt belt disconnected, extremely loose or not installed
properly

- Properly install belt between tilt motor and large

pulley

Tilt/Encoder/Fail

Tilt Encoder Failure

Main board pan/tilt connector (J9) disconnected

- Connect main board pan/tilt connector (J9)

Tilt motor disconnected

- Connect tilt motor power

Encoder faulty

- Replace pan end-of-travel/encoder sensor assembly

Lamp/Strike/Fail

Lamp Strike Failure

Lamp failed to strike after repeated attempts

- Replace lamp

Summary of Contents for VARILITE VL1100 LED Luminaire
























































































Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands

Philips VARILITE VL1100 LED Luminaire, User Manual

Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands