Philips VARILITE VL1100 LED Luminaire User Manual Download Page 78 | Manualshive

Page: 78 / 87

background image

VARI

❋

LITE

®

- VL1100 LED

AND

VL1100 LED HP U

SER

’

S

M

ANUAL

64

13 June 2017

02.1602.0002

Troubleshooting

Error Messages

If a problem occurs during luminaire calibration, at the end of the calibration sequence the Menu
Display will cycle through any applicable error message(s) until the end of the list is reached. To
review the error messages again, it will be necessary to access them using the

Status

function.

To access error messages:

Step 1. Press [

Menu

].

Step 2. Press [

Up

] / [

Down

] arrows until

Fixture

appears. Press [

Enter

].

Step 3. Press [

Up

]/ [

Down

] arrows to access

Status

. Press [

Enter

]. (Display will now scroll

through any error messages or display

OK

if no errors.)

Table A-1: Error Messages

Display

Message...

OK

No Errors Found

Pan/No Sens

Pan sensor not found.

Pan/Encoder/Fail

Pan encoder failure.

Tilt/No Sens

Tilt sensor not found.

Tilt/Encoder/Fail

Tilt encoder failure.

Index/No Sens

Gobo Index sensor not found.

Rot Gobo/No Sens

Rotating Gobo sensor not found.

LED Failure Mode

No message displayed but there will be no response from the LED array.

«
...
76
77
78
79
80
...
»

Summary of Contents for VARILITE VL1100 LED Luminaire
























































































Reviews:

No comments

Related manuals for VARILITE VL1100 LED Luminaire

Brand: Varec Pages: 74

Brand: Halyard Pages: 84

Brand: PAIDI Pages: 48

Brand: Wavetek Pages: 74

Brand: Fairchild Pages: 16

Brand: JB Systems Pages: 12

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: Daekyung Pages: 15

Brand: Hella Gutmann Pages: 48

Brand: Pixlip Pages: 15

Brand: Sove Pages: 29

Fusionchef pearl

Brand: Julabo Pages: 43

Brand: Cattani Pages: 99

CLAMP ON LEAK HiTESTER 3283

Brand: Hioki Pages: 64

Brand: Nightowl Stage Lighting Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands