Philips VARILITE VL1100 LED Luminaire User Manual Download Page 9

Page: 9 / 87

OREWORD

02.1602.0002

13 June 2017

1. Bei Betrieb sind die Außenflächen der Scheinwerfer heiß. Verwenden Sie bei der Bedienung von

aufgeheizter Apparatur die jeweils geeignete Sicherheitsausrüstung (Handschuhe, Augenschutz
etc.).

2. Bei Betrieb der Scheinwerfer ist die Lampe heiß. Unterbrechen Sie die Stromzufuhr und lassen Sie

die Lampe abkühlen, wenn Sie diese austauschen.

3. Bogenlampen senden ultraviolette Strahlen aus, die Hautverbrennungen und Augenentzündungen

verursachen können. Der Betrieb von Bogenlampen erfolgt unter Hochdruck und bei hohen
Temperaturen. Sollte die Lampe zerbrechen, besteht die Gefahr von Körperverletzung bzw. von
Feuer, das von Lampenteilen ausgelöst werden kann.

4. Tragen Sie beim Austausch der Lampen einen Augenschutz.
5. Die geeignete Sicherheitsausrüstung (Handschuhe, Augenschutz) sollte beim Umgang mit

beschädigten Lampen verwendet werden.

6. Wenn die Lampe mit bloßen Händen berührt wird, reinigen Sie sie mit denaturiertem Alkohol und

einem flusenfreien Tuch, bevor Sie die Scheinwerfer installieren oder in Betrieb nehmen.

7. Wenn die Lampe beschädigt oder durch Hitzeeinwirkung deformiert ist, muß diese ausgetauscht

werden.

WARNUNG:
HF-INTERFERENZ

1. Dies ist ein Produkt der Klasse B. In einer häuslichen Umgebung kann dieses Produkt

Funkstörungen verursachen. In diesem Fall kann der Benutzer entsprechende Maßnahmen
ergreifen.

Summary of Contents for VARILITE VL1100 LED Luminaire
























































































Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands

Philips VARILITE VL1100 LED Luminaire, User Manual

Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands