Philips VARILITE VL1100 LED Luminaire User Manual Download Page 39

Page: 39 / 87

NSTALLATION

: A

DDRESSING

02.1602.0002

13 June 2017

Addressing

Program Starting Address

The DMX starting address is entered using the Menu Display. This address will be retained even if the
power is removed.

Note:

Refer to

Chapter 4:

“Menu System” on page 51

for detailed instructions on menu functions.

Note:

Refer to your console operating instructions for specific information regarding its addressing

requirements.

To program a DMX starting address:

Step 1. Press [Menu].
Step 2. Press [Up] / [Down] arrows until

Address

appears. Press [Enter].

Step 3.

DMX

will appear. Press [Enter].

Step 4. Press [Up] / [Down] arrows to enter starting address.
Step 5. Press [Enter] to set.

Program Starting Address Without Calibrating

It is possible to bypass the calibration sequence and go directly to the Menu Display programming in
order to pre-program an address setting.

To program starting address without calibrating luminaire:

•

While powering up luminaire, press and hold [Menu]. Program address as in

Program Starting

Address

above.

•

Release when display reads “:”

Note:

The luminaire will require a reset to restore control.

Summary of Contents for VARILITE VL1100 LED Luminaire
























































































Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands

Philips VARILITE VL1100 LED Luminaire, User Manual

Search results

Summary of Contents for VARILITE VL1100 LED Luminaire

Reviews:

Related manuals for VARILITE VL1100 LED Luminaire

Brands by name

Popular brands