manualshive.com logo in svg

Philips M3000A, Service Manual

The Yamaha M3000A Owner's Manual is a comprehensive guide for operating and maximizing the potential of the Yamaha M3000A mixer. This manual is available for free download at manualshive.com, offering users easy access to essential instructions and insights on this top-of-the-line audio equipment.

Share
Download
background image

Contents

xi

Inspecting the Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

 Inspect Cables and Cords  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Preventive Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

M3046A   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
M3000A / M3001A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Replacement of the Pump and CO

2

 Scrubber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Replacement of the Infrared Lamp  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

General Cleaning of the Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Cleaning Guidelines   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Cleaning Agents   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Battery Handling, Maintenance and Good Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

About the Battery   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Checking the Battery Status  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Charging the Battery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Conditioning a Battery   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Accessing the Battery Status Window   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Battery INOP Messages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Tutorial for Maintaining the Instrument  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Answers to the Tutorial for Maintaining the Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

4  Testing the Instrument  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Objectives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Test Reporting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Recommendations for Test Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Test Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Testing Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Serial Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Visual Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Power On Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Functionality Assurance Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Performance Assurance Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Quick System Check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
System Self-Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
System Self-Test Values  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Preventive Maintenance Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

NBP Accuracy, Leakage, Linearity and Valve Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Sidestream CO

2

 Performance Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Checking and Resetting Time Counters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Documenting CO

2

 Test Results   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Accuracy and Performance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Temperature Accuracy   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
ECG/Resp Performance   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Related manuals for M3000A

Labom BA Series Operating Instructions preview
BA Series
Brand: Labom Pages: 5
OHAUS STARTER 2100 Instruction Manual preview
STARTER 2100
Brand: OHAUS Pages: 19
OHAUS MB23 Instruction Manual preview
MB23
Brand: OHAUS Pages: 54
Zenner MC Assembly Instructions preview
MC
Brand: Zenner Pages: 2
Bartec VOLUTANK Petro 3003 Quick Manual preview
VOLUTANK Petro 3003
Brand: Bartec Pages: 10
ColorLite Rugged 2 User Manual preview
Rugged 2
Brand: ColorLite Pages: 68
Kobold DON-05Bx Operating Instructions Manual preview
DON-05Bx
Brand: Kobold Pages: 55
SATO KEIRYOKI 1410-00 Instruction Manual preview
1410-00
Brand: SATO KEIRYOKI Pages: 2
Bogen AKS16 Installation And Operating Instructions Manual preview
AKS16
Brand: Bogen Pages: 14
Kurzweil SP4 Series Musician'S Manual Addendum preview
SP4 Series
Brand: Kurzweil Pages: 12
Magnescale DF830SLR Instruction Manual preview
DF830SLR
Brand: Magnescale Pages: 2
HyQuest Solutions TB71 User Manual preview
TB71
Brand: HyQuest Solutions Pages: 25
Righton Retinomax K+Screeen Instructions Manual preview
Retinomax K+Screeen
Brand: Righton Pages: 112
Omega FMG490 Series User Manual preview
FMG490 Series
Brand: Omega Pages: 24
Hanna Instruments HI 88703 Instruction Manual preview
HI 88703
Brand: Hanna Instruments Pages: 32
X-Rite RapidMatch GO User Manual preview
RapidMatch GO
Brand: X-Rite Pages: 21
DeNovix DS-11 FX+ User Manual preview
DS-11 FX+
Brand: DeNovix Pages: 93
Fungilab V-Pad Instruction Manual preview
V-Pad
Brand: Fungilab Pages: 47

Brands by name

Popular brands

Load more brands