Philips M3000A Service Manual Download Page 114 | Manualshive

Page: 114 / 293

background image

Mounting Solutions

98

Installing the Instrument

Mounting Solutions

The mounting solutions described in this manual are subject to change. For the latest
information, please visit the Patient Monitoring section of the Philips Medical Systems
website, and follow the links to mounting solutions.

For detailed mounting instructions, refer to the documents supplied with the mounting
hardware.

Installing the Table Mount (M3080A #A10)

The Table Mount is intended for any flat, level surface. To mount the plate securely, you need
4 screws. These are not provided because the type of surface dictates the type of screw.

Step 1

Unpack the Table Mount and check all parts are available.

Step 2

Select 4 screws (appropriate to surface material).

Step 3

Insert the 4 screws through the screw holes provided in the plate.

Step 4

Tighten the screws.

The Monitor snap-fits onto the plate. To release the Monitor, press the button on the front of
the plate.

This mount is also:

• available as support part M3080-63201
• used for the Rollstand mount M3080A #A22

«
...
112
113
114
115
116
...
»

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Related manuals for M3000A

Brand: Keithley Pages: 49

Brand: E Instruments Pages: 2

Brand: Halcyon Pages: 36

Brand: Hameg Pages: 44

Brand: Hameg Pages: 60

Brand: Hameg Pages: 28

Brand: HAMAR LASER Pages: 113

Brand: Yamaha Pages: 31

Brand: Toro Pages: 60

Brand: LORECa Hearing Instrument Pages: 43

Brand: ZIEHL Pages: 37

Brand: XPOtool Pages: 6

Brand: Simex Pages: 48

Digalox DPM72-MPPV

Brand: TDE Instruments Pages: 8

Brand: jenway Pages: 53

Brand: Hanna Instruments Pages: 52

Brand: Cable Detection Pages: 2

Brand: Alcor System Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands