manualshive.com logo in svg

Philips M3000A, Service Manual

The Yamaha M3000A Owner's Manual is a comprehensive guide for operating and maximizing the potential of the Yamaha M3000A mixer. This manual is available for free download at manualshive.com, offering users easy access to essential instructions and insights on this top-of-the-line audio equipment.

Share
Download
background image

Unpacking the Monitor

70

  

Installing the Instrument

Unpacking the Monitor

The box containing your Monitor comes with the following: 

• The Monitor.
• A  Power  Cord.
• The Instructions for Use and Quick Reference Guide (printed).
• Translation Reference for M3/M4 Monitor Texts (non-Roman-8 languages only).
• Documentation CD-ROM including Instructions for Use, Quick Reference Guide, and 

Service Guide.

 

The box containing your Measurement Server contains only the Measurement Server.

The box containing an M3016A Measurement Server Extension contains only the 
Measurement Server Extension.

The box containing an M3015A Measurement Server Extension contains the Measurement 
Server Extension and the associated accessories.

In addition you should receive all of the options and accessories that you have ordered.

If anything is missing, contact your Philips Medical Systems representative immediately.

If anything has been damaged in transit, keep the packing material for inspection and contact 
your Philips Medical Systems representative immediately.

Do not use the Monitor if the casing has been damaged.

If the Monitor is damaged, make sure that the screen is not leaking. There is no known danger 
from the fluid of irritation to skin or eyes, or by inhalation. The median lethal dose if taken 
orally is 2.0g/kg.

 

There are no special procedures necessary for cleaning spilled fluid.

Installing the Monitor

CAUTION

Avoid placing the Monitor, Measurement Server or Measurement Server Extension 
underneath an infusion bag. Make sure that infusion liquid cannot get into any of the 
Measurement or Monitor connectors.

Be sure to read the sections on “Preparing to Install the Monitor” on page 64 and “Unpacking 
the Monitor” on page 70 before continuing.

To install the Monitor you must make sure it has an adequate power supply (see “Preparing to 
Install the Monitor” on page 64 for information about AC power, and the “Using Your 
Monitor in Patient Transport” chapter in the Instructions for Use for information about using 
batteries).

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Related manuals for M3000A

Kawai ES3 Specifications preview
ES3
Brand: Kawai Pages: 2
Datron 1061 Calibration And Servicing Handbook preview
1061
Brand: Datron Pages: 197
janitza FBM Series Manual preview
FBM Series
Brand: janitza Pages: 28
4iiii PRECISION Firmware Upgrade Instructions preview
PRECISION
Brand: 4iiii Pages: 3
Aaronia SPECTRAN V5 Manual preview
SPECTRAN V5
Brand: Aaronia Pages: 47
Kane CO2 Instruction Manual preview
CO2
Brand: Kane Pages: 16
Bacharach Fyrite Tech 50 Instruction, Operation & Maintenance preview
Fyrite Tech 50
Brand: Bacharach Pages: 48
Bacharach HGM300 Installation & Operation Manual preview
HGM300
Brand: Bacharach Pages: 24
Macnaught 050 Manual preview
050
Brand: Macnaught Pages: 14
Galileo VP111 Owner'S Manual preview
VP111
Brand: Galileo Pages: 19
Galileo Milano II Owner'S Manual preview
Milano II
Brand: Galileo Pages: 71
M-system 47LV Operating Manual preview
47LV
Brand: M-system Pages: 18
Parkside PKLL 7 C3 Instructions Manual preview
PKLL 7 C3
Brand: Parkside Pages: 94
QUNDIS Q Water 5.5 Mounting Instructions preview
Q Water 5.5
Brand: QUNDIS Pages: 20
R&S EFL240 Supplement Manual preview
EFL240
Brand: R&S Pages: 2
TASKING MPC5X Hardware User Manual preview
MPC5X
Brand: TASKING Pages: 12
EUPRY P2T1 User Manual preview
P2T1
Brand: EUPRY Pages: 6
REED EMF-822A Instruction Manual preview
EMF-822A
Brand: REED Pages: 4

Brands by name

Popular brands

Load more brands