Philips M3000A Service Manual Download Page 96 | Manualshive

Page: 96 / 293

background image

Installation of Wireless Infrastructure

80

Installing the Instrument

Making the Config Files Writeable

The

Config Files

are read-only and must be made writeable for the tool to be used for

configuration. The following steps describe the procedure after the files have been copied to
the configuring computer:

Step 1

Open the

ConfigFiles

directory by clicking on the

ConfigFiles

folder in the

tools

menu on the configuring PC. The files on the right of the previous figure will be
displayed.

Step 2

Click on the file labelled

WB_WirelessM3_1-2b15.CFG

to select it.

NOTE

The selected file must be made writeable because settings used in the configuration process
are saved to this file so they can be reused when the configuration tool is used again.

Step 3

Place the cursor over either of the highlighted fields and right-click the mouse to
display a menu listing

Properties

, as shown below:

«
...
94
95
96
97
98
...
»

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Related manuals for M3000A

Brand: Kawai Pages: 2

Brand: Datron Pages: 197

Brand: Kane Pages: 12

Brand: E-line Pages: 164

Network Card-MS

Brand: Eaton Pages: 26

Brand: Rayjet Pages: 81

Brand: Omano Pages: 14

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Omega Pages: 20

Brand: Omega Pages: 20

Brand: PASCO Pages: 2

Analite NEP-5000

Brand: Observator Instruments Pages: 103

Brand: R&S Pages: 130

Brand: Eno Scientific Pages: 47

Brand: Z-TRAUQ Pages: 10

Brand: Hanna Instruments Pages: 11

Brand: Eddyfi Technologies Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands